DUORO SERVICES Australia

 

yaesu 93x20.jpg - 3.97 Kb yaesu 93x20.jpg - 3.97 Kb yaesu 93x20.jpg - 3.97 Kb yaesu 93x20.jpg - 3.97 Kb 

 

YAESU

Spare Parts etc

 

Kur02 page updated 24/09/2020

 

NOTE 1:- IF THE PARTS YOU WANT ARE NOT LISTED BELOW. Please Check The KENPRO Parts Page.

NOTE 2 :- Yaesu purchased Kenpro's (KR etc) rotator product line in the early 1990's & replaced the "KR" prefix with "G".

 

ALINCO etc   CDE    COMMON   CREATE   EMOTATOR   HYGAIN   KENPRO 

 

  Click For SALES & To CONTACT Duoro Services  

 

PayPal LogoPayPal Logo

 

 Click For PURCHASING Details  

PayPal LogoPayPal Logo

 

All prices are in Australian Dollars (AUD) & include GST

 

STOCK AVAILABLE NEW, SECOND HAND & REFURBISHED SPARE PARTS ETC
QTY QTY QTY YAESU YAESU $..AUD...
NEW USED Refurb Part No. & Image Description ...Each
10    

 yLED-dc

NEW - yLED-dc. Replacement display illumination LED PCB for Yaesu DXA, DXC & SA controller for G-800, G-1000 & G-2800 rotators.
Comes standard with 3 x square white LED's, Brightness adjustment via trim POT, Current limiting protection resistor, Terminal block for non soldering installation + full install instructions with 10 colour pics.

Tools require for easy installation:- No. 2 philips screwdriver, Side cutters &/or wire strippers, Small philips screw driver, Trim POT adjuster flat screw driver, Black marker & Watch the yLED-dc video.

Australia wide postage ($10.00) (for up to 10 PCB's) is via prepaid small satchel, Packaging & handing included in the freight price, Preferred payment is via EFT/Bank transfer/Direct deposit etc, Please supply full name & delivery address so I will send you a complete invoice with my bank details.

 Watch the video on YouTube

$  22.ea
8    

 yLED-ac

 NEW - yLED-ac. Replacement display illumination LED PCB for YAESU G-800s, G-1000s & G-1300 controllers, Also KENPRO KR-800s, KR-1000s & HR-1300 controllers.
Comes standard with 3 x square white LED's, Brightness adjustment via trim POT, Current limiting protection resistor, Bridge rectifier & 470uF 16v CAP (for minimal AC pulsing operation), Terminal block for non soldering installation + full install instructions with 10 colour pics.

Tools require for easy installation:- No. 2 philips screwdriver, Side cutters &/or wire strippers, Small philips screw driver, Trim POT adjuster flat screw driver & Watch the yLED-ac videos.

Australia wide postage ($10.00) (for up to 10 PCB's) is via prepaid small satchel, Packaging & handing included in the freight price, Preferred payment is via EFT/Bank transfer/Direct deposit etc, Please supply full name & delivery address so I will send you a complete invoice with my bank details.

Watch the yLED-ac KR-800 video on YouTube

Watch the yLED-ac G-1300 video on YouTube

$  24.ea
           
G-1000 rotator (same as Kenpro KR-1000), listed parts sold separately below
  1  

8601-002

G-800/1000 or KR-800/1000 (PC-8601-002) Rotator Top Housing in very good condition.

The mast clamp mounting threaded holes have been upgraded with Stainless Steel M8 RECOILS. 

$  95.00
   

Coming

Soon

KR/G-800GMA

Gear Motor Assembly For KR-800 or Yaesu G-800.

Refurbished & in good condition gear & motor assembly.

Has been completely stripped down, cleaned & reassembled with new grease through out, ready to install into housing. Wiring is numbered for the socket.

$ TBA
  1  

1000MA

G-1000 Rotator Motor Assembly inc motor, plate, brake housing & BK spring, RF shield & wiring + damaged Pinion. sold as is. $  65.00
  1  

1000SB

G-1000 Rotator Swing Bar with retainers (for limit switches & end stop) in good condition. Sold as is. $   8.00
     

 

  $   
  1  

G-CS7p

7 Pin chassis socket for rotator inc. rubber washer $  5- ea
 
NEW USED Refurb Part No. & Image Description $  AUD

8

   

POT-500N

RA25Y20s

NEW Potentiometer 500ohm (by COSMOS) for Daiwa, Kenpro, Yaesu etc rotator's & full circle controllers. These new POT's have end stops in them, so when installing them make sure you align them properly. New Lower Price. $  40.ea

1

   

GC-038

NEW mast clamps for Yaesu & Kenpro Rotators $   89.ea
1    

GC-048-6

NEW Mast Clamp (6 bolt clamping not 4) for Yaesu G-2700, G-2800 & Kenpro KR-2000 & KR-2700 & HR-2700 etc rotators. Can also be used as a lower mast clamp most Kenpro & Yaseu rotators.  $  129.ea